ISO 29463 / EN 1822
EN 1822 anchors EPA, HEPA, and ULPA filter performance testing and marking.
AlignedHEPA and ULPA filter studies covering efficiency and penetration near the most penetrating particle size (MPPS), plus pressure-drop measurements.
Connect EN 1822 or ISO 29463 method choices with aerosol challenge controls, sampling records, and the evidence behind reported high-efficiency filter results.
EN 1822 and ISO 29463 form the citation set; ARE Labs translates them into MPPS targeting, airflow control, upstream/downstream measurement, QA records, and report outputs.
EN 1822 anchors EPA, HEPA, and ULPA filter performance testing and marking.
AlignedISO 29463 provides the international high-efficiency filter and filter-media framework, including classification, performance, testing, marking, an...
AlignedFor HEPA and ULPA filters, a critical question is particle penetration at or near the most penetrating particle size. This cluster covers EN 1822 and ISO 29463 method selection, aerosol challenge conditions, upstream and downstream measurement, pressure-drop tracking, repeatability, and documentation. It also distinguishes ARE Labs testing from product certification:
This cluster follows high-efficiency filtration evidence from aerosol generation and particle sizing to concentration measurements, operating conditions, calculations, and deviations. It explains how those records inform interpretation in the final report.
The cluster applies when EPA, HEPA, or ULPA performance depends on MPPS targeting, upstream/downstream sampling, pressure drop, and traceable fixture or device configuration.
This page is a standards cluster, not a certification page or a reproduction of protected standard text. EN 1822 and ISO 29463 give the high-efficiency filter frame for classification, performance testing, marking, particle measurement, and documentation. ARE Labs uses them to build protocol controls and report evidence for product development, validation, and claims support.
High efficiency air filters (EPA, HEPA and ULPA) - Classification, performance testing, marking
EN 1822 anchors EPA, HEPA, and ULPA filter performance testing and marking. For ARE Labs studies, it informs MPPS-focused challenge design, particle measurement, leakage context, pressure-drop recording, fixture documentation, and report language for efficiency and penetration evidence.
BSI official publisher page for BS EN 1822-1:2019 verified 2026-05-17.
High efficiency filters and filter media for removing particles in air - Part 1: Classification, performance, testing and marking
ISO 29463 provides the international high-efficiency filter and filter-media framework, including classification, performance, testing, marking, and documentation. ARE Labs uses it to align aerosol generation, particle counting, efficiency, penetration, leak-related observations, and reporting when the program cites the ISO series.
ISO official page for ISO 29463-1:2024 verified 2026-05-17.
ARE Labs is ISO/IEC 17025-accredited for its current testing scope. EN 1822 and ISO 29463 are aligned method references for these filter studies. Reports identify the tested configuration, applicable procedure and deviations.
The standards set the filter-performance frame, and ARE Labs builds the executable method around filter format, airflow range, fixture interface, aerosol source, particle measurement path, and client decision.
We translate EN 1822 or ISO 29463 into a fixture plan covering filter orientation, seal approach, airflow range, pressure taps, and sampling locations.
Protocol setupAerosol generation, particle sizing, background control, and upstream concentration checks are selected to support the EN 1822 or ISO 29463 decision point.
Challenge recordUpstream and downstream particle measurements, airflow, pressure drop, temperature, humidity, and run timing are recorded against the ISO 29463 or EN 1822 frame.
Traceable run logWhen a housing, purifier, duct, or respirator component does not match EN 1822 fixtures, ARE Labs records the ISO 29463 rationale and limits.
Adaptation rationaleReports connect EN 1822 or ISO 29463 citations to efficiency, penetration, pressure drop, conditions, calculations, deviations, and method limitations.
Review-ready reportHigh-efficiency filter results depend on stable challenge conditions, traceable measurements, and clear calculations. For EN 1822 and ISO 29463 studies, ARE Labs documents fixtures, instrument checks, raw particle data, pressure-drop evidence, deviations, and QA review. These records show the client how each result was produced.
EN 1822 and ISO 29463 runs link fixture configuration, filter orientation, airflow, pressure drop, and sampling locations to the chosen study frame.
ISO 29463 documentation keeps aerosol generation, particle sizing, background control, temperature, humidity, and challenge stability visible in the review trail.
ISO 29463 / EN 1822 data packages retain upstream and downstream particle results, efficiency, penetration, pressure drop, calculations, and instrument references.
When product geometry falls outside EN 1822 or ISO 29463 assumptions, ARE Labs records the rationale, limitation, and interpretation impact.
ISO 17025 review distinguishes ARE Labs test evidence from third-party certification, product listing, or regulatory approval.
ARE Labs connects technical topics to practical study design, method selection, controlled aerosol work, and reportable evidence without turning technical pages into sales pages.
These questions help product, quality, and regulatory teams choose between EN 1822, ISO 29463, and a fit-for-purpose protocol for HEPA and ULPA filter work. They explain how standards-aligned testing differs from certification and describe the records ARE Labs prepares for technical review before issuing the final report.
Q. Which standard applies?
A. EN 1822 and ISO 29463 are both used for high-efficiency EPA, HEPA, and ULPA filters. The choice depends on product form, target market, claim language, and whether the program needs classification support, penetration data, leak context, or development evidence.
Q. Does ARE Labs certify HEPA filters?
A. No. ARE Labs performs testing aligned with the cited standard. A separate authority or certification body handles certification, listing, or formal product classification.
Q. What if my device is not a standard filter?
A. ARE Labs can build a fit-for-purpose protocol for purifiers, duct systems, respirator components, or nonstandard housings. The protocol and report document deviations, the reasons for them, and limits on interpreting the results.
Q. What data does the report include?
A. Reports can include fixture details, operating conditions, upstream and downstream particle results, efficiency, penetration, pressure drop, calculations, calibration references, QC checks, deviations, and data exclusions.
Q. Why are publisher links included?
A. Official BSI and ISO links let clients confirm the exact standard family, status, scope, and purchase source without relying on unofficial copies or summaries.
HEPA and ULPA MPPS work sits near other filtration, air-cleaning, and particle-control clusters. These routes help teams move from high-efficiency filter evidence into ventilation, room-cleaner, emissions, or sorbent questions.